Skip to content

Compact Liquid Cooling Plate for Medical Equipment

Drawing-led engineering Extrusion + machining Inspection planning

A compact liquid cooling plate for medical equipment, developed around heat load, low-noise cooling, service access and clean assembly requirements.

Custom requirement?

Review the profile and the finished component together.

Send the drawing, material, finish, critical tolerances and estimated quantities. We will confirm the engineering route before quotation.

Request a technical quote

Compact liquid cooling plate for medical equipment is specified around the complete thermal and mechanical job. A compact liquid cooling plate for medical equipment is often specified where fan noise, enclosure size or component density limit air cooling. The plate has to remove heat while fitting into a serviceable assembly and supporting the documentation expected by the equipment builder.

Compact liquid cooling plate for medical equipment: starting parameters

Medical systems may run intermittently, produce short high-load pulses or require stable temperature near sensitive detectors and electronics. Those duty patterns influence channel design and control strategy. The mechanical team also needs to consider connector access, drainability, cable routing and protection during cleaning or service.

Part numberHIQ-CP-MED-425
Reference envelope425 x 357 x 39 mm
Reference sample mass4.7 kg
Reference temperature range-40 C to 150 C
Cooling methodClosed-loop liquid cooling
OrientationVertical reference layout
Body material routeAluminum, grade and temper confirmed for the project
Secondary operationsCNC machining, drilling, port preparation and finish
CustomizationOutline, channels, ports, mounting holes and finish
AcceptanceDrawing-based dimensional, surface and leak-test plan

The dimensions, mass and temperature range shown here come from the supplied reference sample and are useful for an initial layout review. HIQ confirms the final drawing, aluminum alloy, joining route, port specification and test requirements before production.

Critical decisions for this medical imaging and electronic systems application

A successful cooling plate must do more than provide a large metal area. The following points should be resolved before tooling and sample approval:

  • Heat-source footprint, total load and maximum allowable component temperature
  • Coolant type, inlet temperature, flow rate and acceptable pressure drop
  • Thermal-interface flatness, surface condition and mounting pressure
  • Port direction, connector type, service clearance and hose routing
  • Machining access for mounting holes, pockets, threads and sealing features
  • Leak-test method, cleanliness, finish and traceability requirements

These questions help distinguish a visually similar plate from one that can be assembled and validated predictably. Where the application already has a working design, send the drawing, test history and known failure points so the review can focus on the interfaces that need improvement.

How HIQ turns the reference into a production cooling plate

The production route combines thermal-path review, aluminum profile or plate selection, CNC machining, coolant-circuit preparation, surface finishing and inspection. The sequence is planned around the finished interface rather than around one manufacturing process.

  1. Application and drawing reviewClarify heat load, coolant conditions, module footprint, assembly access, annual volume and critical interfaces.
  2. Thermal and DFM routeCheck spreading area, channel or machined-flow concept, wall support, port location and machining access.
  3. Material and joining reviewSelect an aluminum route and joining method that fit the coolant, strength and leak-test requirements.
  4. Machining and finishPrepare contact surfaces, mounting features, threads and ports, then apply the agreed protection or coating.
  5. Inspection and packingMeasure functional dimensions, verify the cooling circuit as specified and protect sealing surfaces for shipment.

Applications for medical imaging and electronic systems

Typical uses include imaging electronics, laser and optical power supplies, laboratory instruments and compact diagnostic systems. The reference cold-plate envelope can be adapted to different board layouts; however, the intended thermal duty, coolant, cleaning process and regulatory requirements must be defined by the equipment project.

The reference enclosure is intentionally adaptable. A buyer can use it as a starting point for a new housing, a replacement plate or a family of related products. Final performance must still be established with the actual module, coolant loop and mounting condition; published outline dimensions alone cannot guarantee a system temperature.

Quality controls for a sealed aluminum cooling plate

Inspection should be proportionate to the application. Dimensional reports can cover the mounting and thermal surfaces, while process records can address joint integrity, cleanliness and leak testing. Any claim about a medical-compatible finish or cleanroom condition must come from the approved project specification, not from a generic product description.

  • Outline and mounting-hole position against the approved datums
  • Thermal-interface flatness and agreed surface condition
  • Port location, thread or fitting condition and torque requirements
  • Leak-test pressure, medium, duration and allowable leak rate
  • Visual condition, cleanliness and protective packaging

For material and process context, review the Aluminum Association and ASTM International. Use the approved project drawing and test plan for final acceptance.

RFQ checklist for HIQ-CP-MED-425

  • 2D drawing or 3D model with the current revision
  • Heat-source layout, total heat load and allowable temperature rise
  • Coolant, flow rate, inlet temperature and pressure-drop target
  • Port thread or connector standard, tubing route and service access
  • Material, finish, leak-test and inspection requirements
  • Prototype quantity, annual volume and sample timing

Review the liquid-cooled heat sink range, compare the IGBT water-cooled heat sink plates, or send the module drawing to HIQ Aluminum for a technical review.

Compact Liquid Cooling Plate for Medical Equipment FAQs

Can a quiet cooling system be developed?

Liquid cooling can move heat away from the equipment enclosure, but pump, fan and flow-path noise must be evaluated as part of the complete system.

Can the plate be made smaller than the reference?

Yes, provided the heat load, thermal spreading area, flow path and mounting features can be maintained. A smaller outline may require a different internal design.

Which documentation can be discussed?

Dimensional inspection, material records, surface conditions and leak-test results can be scoped to the drawing and purchasing requirements.

Contact us

Phone: (+86) 84790021
Fax: (+86) 84790020

Need help or have a question?
Contact us at: [email protected]

369 Songhua Road
Qingpu District Shanghai China 201706

Account

  • Products
  • My Account
  • My Wishlist
  • My Cart
  • Sign In
  • Hot Offers
  • Checkout

Useful Links

Email Newsletter

Subscribe to our newsletter and get 10% off your first purchase